Access point Aruba (HPE) R4W43A
1870 $
Access points Aruba (HPE) provide fast and stable wireless data transmission in a corporate network. Aruba offers both simple devices for providing basic Wi-Fi network functionality, and for networks with high user density and speeds up to 2 Gbit/s, as well as protected models for operation in difficult climatic conditions.
Access points are easy to install, can work simultaneously in ranges 2,4 And 5 GHz, use technology MIMO to increase the data transfer rate and support the standard 802.11ac Wave2.
Instant-Access points Aruba — do not require a separate controller, but use a virtual controller, the functions of which are performed by one of the points. HPE Aruba Instant — is a solution that allows you to deploy an "controlless" enterprise-grade WiFi network. It already has built-in network security, automatic management RF and enough smart features to run a complete solution without additional licensing. A cluster of access points is controlled using a virtual controller, which is located on one of the access points (IAP). The controller is responsible for the process of autoconfiguring new access points, authorization and authentication, guest access and network services (NAT, DHCP and etc.).
Specifications Access points Aruba (HPE) R4W43A:
|
R4W43A Specification |
|
|
Hardware Variants |
Built-in Omni Directional Antennas 5 GHz Antennas 5.4 dBi 2.4 GHz Antennas 3.2 dBi BLE/802.15.4 Antennas 3.3d Bi |
|
Wi-Fi Radio Specifications |
|
|
AP type |
Outdoor Hardened, Wi-Fi 6 dual radio, 5 GHz 2x2 MIMO and 2.4 GHz 2x2 MIMO Software-configurable dual radio supports 5 GHz (Radio 0) and 2.4 GHz (Radio 1) |
|
5GHz
|
Two spatial stream Single User (SU) MIMO for up to 1.2 Gbps wireless data rate with individual 2SS HE80 802.11ax client devices, or with two 1SS HE80 802.11ax MU-MIMO capable client devices simultaneously |
|
2.4GHz
|
Two spatial stream Single User (SU) MIMO for up to 574 Mbps (287 Mbps) wireless data rate with individual 2SS HE40 (HE20) 802.11ax client devices or with two 1SS HE40 (HE20) 802.11ax MU-MIMO capable client devices simultaneously |
|
Available channels |
Dependent on configured regulatory domain |
|
Supported radio technologies
|
802.11b: Direct-sequence spread-spectrum (DSSS) 802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM) 802.11ax: Orthogonal frequency-division multiple access (OFDMA) with up to 16 resource units (RU) |
|
Supported modulation types
|
802.11b: BPSK, QPSK, CCK 802.11a/g/n: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM (proprietary extension) 802.11ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM, 1024-QAM (proprietary extension) 802.11ax: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM, 1024-QAM |
|
802.11n high-throughput (HT) support |
HT 20/40 |
|
802.11ac very high throughput (VHT) support |
VHT 20/40/80 |
|
802.11ax high efficiency (HE) support |
HE20/40/80 |
|
Transmit power |
Configurable in increments of 0.5 dBm |
|
Maximum (conducted) transmit power (limited by local regulatory requirements)
|
2.4 GHz band: +23 dBm per chain, +26 dBm aggregate (2x2) 5 GHz band: +23 dBm per chain, +26 dBm aggregate (2x2) Note: conducted transmit power levels exclude antenna gain. |
|
Maximum EIRP (limited by local regulatory requirements):
|
2.4 GHz band: 565: 29.2 dBm EIRP 567: 33 dBm EIRP 5 GHz band: 565: 31.4 dBm EIRP 567: 32.7 dBm EIRP |
|
Power |
|
|
Maximum (worst-case) power consumption |
15.6W |
|
Maximum (worst case) power consumption in idle mode |
4.2W |
|
Maximum (worst case) power consumption in deep-sleep mode |
1.7W |
|
Power over Ethernet (PoE+) |
802.3at-compliant |
|
Mechanical |
|
|
Dimensions |
16.5 cm (W) x 16.5 cm (D) x 11 cm (H) 6.5” (W) x 6.5” (D) x 4.3” (H) |
|
Environmental |
|
|
Operating temperature |
-40° C to +55° C (-40° F to +140° F) with full solar loading |
|
Operating humidity |
5% to 95% non-condensing internal |
|
Storage and transportation temperature: |
-40° C to +70° C (-40° F to +158° F) |
| condition | new |
|---|
Log In