Access points Aruba (HPE) Provide fast and stable wireless data transmission in the corporate network.. Aruba offers both simple devices for providing basic Wi-Fi network functionality, and for networks with high user density and speeds up to 2 Gbit/s, as well as protected models for operation in difficult climatic conditions.
Access points are easy to install, can work simultaneously in the bands. 2,4 and 5 GHz, use technology MIMO to increase the data transfer rate and support the standard 802.11ac Wave2.
Instant-Access points Aruba — do not require a separate controller, but use a virtual controller, the functions of which are performed by one of the points. HPE Aruba Instant — is a solution that allows you to deploy «controllerless» enterprise WiFi network. It already has built-in network security, automatic management RF and enough smart features to run a complete solution without additional licensing. A cluster is controlled from access points using a virtual controller, which is placed on one of the access points. (IAP). The controller is responsible for the process of autoconfiguring new access points, authorization and authentication, guest access and network services (NAT, DHCP and etc.).
Specifications Access points Aruba (HPE) JW182A:
|
AP-228 SPECIFICATIONS
|
- 2.4-GHz (600 Mbps max) and 5-GHz (1.3 Gbps max) radios, each with 3x3 MIMO and three combined, diplexed external antenna connectors.
|
|
WIRELESS RADIO SPECIFICATIONS
|
- AP type: Indoor, dual radio, 5 GHz 802.11ac and 2.4 GHz 802.11nSoftware-configurable dual radio supports 5 GHz and 2.4 GHz
- In addition to 802.11n data rates, the 2.4-GHz radio supports 802.11ac data rates using 256-QAM modulation. This gives TurboQAM-enabled clients a 33% boost above the maximum supported data rate.
- 3x3 MIMO with three spatial streams and up to 1.3 Gbps wireless data rate
- Supported frequency bands (country-specific restrictions apply):Available channels: Dependent on configured regulatory domain
- 2.4000 GHz to 2.4835 GHz
- 5.150 to 5.250 GHz
- 5.250 to 5.350 GHz
- 5.470 to 5.725 GHz
- 5.725 to 5.850 GHz
- Dynamic frequency selection (DFS) optimizes the use of available RF spectrum
- Supported radio technologies:
- 802.11b: Direct-sequence spread-spectrum (DSSS)
- 802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM)
- 802.11n/ac: 3x3 MIMO with up to three spatial streams
- Supported modulation types:Transmit power: Configurable in increments of 0.5 dBm
- 802.11b: BPSK, QPSK, CCK
- 802.11a/g/n: BPSK, QPSK, 16-QAM, 64-QAM
- 802.11ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM
- Maximum (aggregate, conducted total) transmit power (limited by local regulatory requirements):Advanced Cellular Coexistence (ACC) feature to effectively deal with interference from cellular systems
- 2.4-GHz band: +28 dBm (23 dBm per chain)
- 5-GHz band: +28 dBm (23 dBm per chain)
- Maximum ratio combining (MRC) for improved receiver performance
- Cyclic delay diversity (CDD) for improved downlink RF performance
- Short guard interval for 20-MHz, 40-MHz and 80-MHz channels
- Space-time block coding (STBC) for increased range and improved reception
- Low-density parity check (LDPC) for high-efficiency error correction and increased throughput
- Transmit beam-forming (TxBF) for increased reliability in signal delivery
- Supported data rates (Mbps):802.11n high-throughput (HT) support: HT 20/40
- 802.11b: 1, 2, 5.5, 11
- 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54
- 802.11n: 6.5 to 450 (MCS0 to MCS23)
- 802.11ac: 6.5 to 1,300 (MCS0 to MCS9, NSS = 1 to 3)
- 802.11ac very high throughput (VHT) support: VHT 20/40/80
- 802.11n/ac packet aggregation: A-MPDU, A-MSDU
|
|
POWER
|
- Worst-case power consumption from the AP: 23W
- Power sources sold separately
- Power over Ethernet (PoE+): 802.3at-compliant
|
|
OTHER INTERFACES
|
- Two 10/100/1000BASE-T Ethernet network interfaces (RJ-45)Serial console interface (Micro USB)
- Auto-sensing link speed and MDI/MDX
- Load balancing support to achieve platform throughput greater than 1 Gbps
- PoE-PD: 802.3at PoE+
|
|
MOUNTING
|
- Optional mounting kits
- AP-220-MNT-W1 is directly compatible
- 270 Series outdoor AP mounts (AP-270-MNT-V1, AP-270-MNT-V2, AP-270-MNT-H1, AP-270-MNT-H2) are compatible when the AP-270-MNT-ADP adapter is utilized
|
|
MECHANICAL
|
- Dimensions/weight (unit, excluding mount accessories):
- 222 mm (L) x 150 mm (W) x 75 mm (H), 8.5” (L) x 6” (W) x 2.5” (H)
- 1.225 kg/2.700 lbs
|
|
ENVIRONMENTAL
|
- Operating:
- Temperature: -40° C to +60° C (-40° F to +140° F)
- Humidity: 5% to 95% non-condensing
- Storage and transportation:
- Temperature: -40° C to +70° C (-40° F to +158° F)
- Operating Altitude: 3,000 m
|
|
ANTENNAS
|
- Six RP-SMA connectors for external antennas
|
|
REGULATORY
|
- FCC/Industry of Canada
- CE Marked
- R&TTE Directive 1995/5/EC
- Low Voltage Directive 72/23/EEC
- EN 300 328
- EN 301 489
- EN 301 893
- UL/IEC/EN 60950
- EN 60601-1-1 and EN 60601-1-2
- For more country-specific regulatory information and approvals, please see your Aruba representative.
|
|
REGULATORY MODEL NUMBERS
|
- AP-228 and IAP-228: APIN0228
|
|
CERTIFICATIONS
|
- CB Scheme Safety, cTUVus
- UL2043 plenum rating
- Wi-Fi Alliance (WFA) certified 802.11a/b/g/n/ac
|
|
WARRANTY
|
- Aruba limited lifetime warranty
|
|
MINIMUM SOFTWARE VERSION
|
- ArubaOS 6.4.3.0
- Aruba Instant 4.2.0
|
Log In