Module Cisco SPA-OC192POS-XFP

Product compatibility

• Cisco ASR 1000 Series Router

• Cisco ASR 9000 Series Router

Port density per SPA

• 1 port

• DPT/RPR configuration - two SPAs are needed to connect to one RPR ring

Physical interface

• OC-192c/STM-64c fixed interface or pluggable (XFP) optics module

• Connector:

• XFP-LC connector

• Long reach (LR)-SC connector

• Very short reach (VSR)-Standard media termination point (MTP) (multipath optical [MPO]) multifiber optical connectors

• RPR operation requires a mate cable-part number CBL-RPR-OC192-L or CBL-RPR-OC192-S

• Visual status indicators (LEDs):

• SPA status LED

• Per-port LEDs

• Carrier and alarm

• Active and loopback

• Protect

• Pass-through

Protocols

• High-Level Data Link Control (HDLC), RFC 2615

• Point-to-Point Protocol (PPP), RFC 1662

• Frame Relay, RFC 2427

• IPv4/IPv6

• IEEE 802.17 RPR

• IETF 2892-SRP

Features and functions

• Synchronization

• Local (internal) or loop timed (recovered from network)

• Layer 3 clock accuracy (± 4.6 ppm) over full operating temperature

• Pointer activity monitoring

• Local (diagnostic) and line (network) loopback

• Section data communication channel (SDCC) -platform-dependent feature

• Payload mapping

• 1 + x^43 self-synchronous scrambler

• SONET/SDH compliance

• Telcordia (Bellcore) GR-253-CORE (as applicable)

• ANSI T1.105, and T1.231

• ITU-T G.707, G.957, and G.825 (as applicable)

• Supported SONET/SDH alarm and signal events

• Signal failure bit error rate (SF-ber)

• Signal degrade bit error rate (SD-ber)

• Signal label payload construction (C2)

• Path trace byte (J1)

• Section

• Loss of signal (LOS)

• Loss of frame (LOF)

• Error counts for B1

• Threshold crossing alarms (TCA) for B1

• Error counts for B2

• Threshold crossing alarms (TCA) for B2

• Line

• Line alarm indication signal (LAIS)

• Line remote defect indication (LRDI)

• Line remote error indication (LREI)

• Path

• Path alarm indication signal (PAIS)

• Path remote defect indication (PRDI)

• Path remote error indication (PREI)

• Error counts for B3

• TCA for B3

• Loss of pointer (LOP)

• Positive stuffing event (PSE)

• Negative stuffing event (NSE)

• Path unequipped indication signal (PUNEQ)

• Path payload mismatch indication signal (PPLM)

Network management

• RFC 2558 MIB (SONET/SDH)

• Simple Network Management Protocol (SNMP)

Reliability and availability

• Online insertion and removal (OIR)

• Field-replaceable XFP optical modules

• 1 + 1 SONET automatic-protection-switching (APS) and SDH linear multiplex-section-protection (MSP) protocols

• Single SPA software reset

Physical specifications

• Weight: 0.75 lb (0.34 kg)

• Height: 0.8 in. (2.03 cm) (single height - XFP interface)

• Height: 1.6 in. (4.06 cm) (double height - VSR, LR fixed optics)

• Width: 6.75 in. (17.15 cm)

• Depth: 7.28 in. (18.49 cm)

Power

15.5W maximum

Environmental specifications

• Operating temperature: 41 to 104°F (5 to 40°C)

• Storage temperature: -38 to 150°F (-40 to 70°C)

• Operating humidity: 5 to 85% relative humidity

• Storage humidity: 5 to 95% relative humidity

Compliance and agency approvals

Safety

• UL 60950

• CSA 22.2-No.60950

• EN60950

• IEC 60950 CB Scheme

• ACA TS001

• AS/NZS 3260

• EN60825\IEC60825 laser safety (SR, IR-Class 1) (VSR-Class 1M)1

• 21CFR1040-FDA Code of Federal Regulations (USA) laser safety (SR, IR-Class 1) (VSR-Class 1M)1

EMC

• FCC Part 15 (CFR 47)

• ICES 003

• EN55022

• CISPR 22

• AS/NZ 3548

• VCCI

• EN55024

• EN50082-1

• EN61000-6-1

• EN61000-3-2

• EN61000-3-3

Network Equipment Building System (NEBS)

This product is designed to meet the following requirements (official qualification may be in progress):

• SR-3580-NEBS: Criteria levels (Level 3 compliant)

• GR-63-Core-NEBS: Physical protection

• GR-1089-Core-NEBS: EMC and safety

ETSI

• EN300 386/EN300 386-2 Class B

• ETS 300 019 Storage Class 1.1

• ETS 300 019 Transportation Class 2.3

• ETS 300 019 Stationary Use Class 3.1