|
Chassis compatibility
|
All Catalyst 4500 E-series switches
|
|
Software requirements (minimum)
|
Refer to your software release notes for the latest software release requirements
|
|
Chassis slot restrictions
|
•Catalyst 4503-E: Slot 1 only
•Catalyst 4506-E: Slot 1 only
•Catalyst 4507R-E and Catalyst 4507R+E: Slot 3 and slot 4
•Catalyst 4510R-E and Catalyst 4510R+E: Slot 5 and slot 6
|
|
Bandwidth per slot
|
48-Gbps
|
|
Memory
|
2-GB (upgrade to 4-GB)
|
|
STATUS LED
|
The status LED indicates the current health of the supervisor engine and the current software state.
|
|
RESET switch
|
The RESET switch is used to reset and restart the switch.
Note Use a paper clip or other small, pointed object to press the RESET switch.
|
|
ACTIVE SUP LED
|
The active supervisor engine LED indicates whether the supervisor engine is active or in standby mode in redundant supervisor engine configurations.
|
|
UTILIZATION LEDs
|
Eight LEDs indicate (as an approximate percentage) the current traffic load over the backplane.
|
|
USB connectors
|
Two USB 2.0 ports are provided. Port 1 operates in device mode (upstream) and port 2 in host mode (downstream). Port 1 has a standard Type B USB connector and can be used as a USB console.Port 2 has a USB type A connector and a standard USB 2.0 device like a flash memory device can plug into this connector.
|
|
SECURE DIGITAL slot
|
A standard Secure Data (SD) memory card interface is provided on the front panel
|
|
CONSOLE port
|
This is a 10/100/1000 port that uses an RJ-45 connector. The console port allows you th access the switch either locally (with a console terminal) has an RJ-45 connector. The console port allows you to perform the following functions:
•Configure the switch from the CLI
•Monitor network statistics and errors
•Configure SNMP agent parameters
|
|
10/100/1000 MGT port
|
The Ethernet management port is a Layer 3 host port to which you can connect a PC. You can use the Ethernet management port instead of the switch console port for network management. When managing a switch, connect the PC to the Ethernet management port on a Catalyst 4500 E-series switch.
Note When connecting a PC to the Ethernet management port, you must assign an IP address.
|
|
LINK LED
|
The 10/100/1000 MGT port has a link LED associated with it.
|
|
1G/10G UPLINKS (SFP/SFP+) ports
|
The Supervisor Engine 7-E has four 1-G or 10-G ports that use either SFP transceivers or SFP+ transceivers.
|
|
Uplink port LEDs
|
Each of the four uplink ports has two LEDs associated with it. One LED displays port status when a 1-GB SFP transceiver is installed in the port socket. The second LED displays uplink port status when a 10-GB SFP+ transceiver is installed in the port socket.
|
|
Power requirement
|
302 W
|
|
Operating temperature
|
Certified for operation: 32° to 104°F (0° to 40°C)
•Designed and tested for operation: 32° to 130°F (0° to 55°C)
|
|
Humidity (RH) ambient (noncondensing)
|
10 to 90%
|
|
Operating altitude
|
Certified for operation: 0 to 6500 ft (0 to 2000 m)
•Designed and tested for operation: -200 to 10,000 ft (-60 to 3000 m)
|
|
Operating temperature
|
Certified for operation: 32° to 104°F (0° to 40°C)
•Designed and tested for operation: 32° to 130°F (0° to 55°C)
|
Log In