Interface boards or line cards Juniper Networks (line card, interface module) allow you to expand your router or switch (modular platform, chassis) Required functional, including the necessary access ports at speeds 1GbE, 10GbE, 40GbEor 100GbE, control boards (switch control board) etc..
Interface boards Juniper represented by various modules that are compatible with a particular series (for example. interface module MS-MIC-16G compatible with the entire range Juniper MX, and the module MPC-3D-16XGE-SFPP series compatible MX240, MX480 andMX960).
interface board MIC (Modular Interface Cards) is a small-sized module that provides physical connection to various types of network devices. MIC the board can support various physical interfaces in one module. module Juniper MICs also support hot swapping and plugging. For example, in routers MX series, interface module MIC installed in the module MPC (Modular Port Concentrator), and in series from MX5 before MX104 module MPC already built in chassis.
interface module Juniper MPC (Modular Port Concentrator) provides transfer services Lkand packages. module MPC encapsulates packets and passes them through the module's outgoing interfaces MIC. everyone MPC module equipped with up to four chipsets Junos Trio, which performs the functions of management. For example, a router Juniper MX960 supports installation of up to 12 modules MPCs, and the platform MX480 before 3 MPCs. For proper operation module Juniper MPC You need to use high-performance cooling modules. Online Juniper http://www.juniper.net there is a calculator for calculating the recommended power and cooling power, for a specific series and used MPC modules.
Interface modules DPC (Dense Port Concentrators) Provides several physical interfaces and pass systems Lkand packages on a single board that fits into a slot in a router or modular chassis. module DPC accepts incoming packets and sends outgoing packets to the network.
module Juniper PIC (Physical Interface Card) installed in FPC (Flexible PIC Concentrators), similar to how they work MIC andMPC modules. PICs modules provide physical interfaces, and FPCs boards provide transfers Lkfor packets on the network. everyone FPCthe module is equipped with a microchip ASIC, which performs the functions of management, and FPC supports installation of 2 modules PIC.
Technical characteristics of the interface module Juniper MIC-3D-4OC3OC12-1OC48:
|
Software release
|
- 4-port: Junos OS Release 11.2 and later
- 8-port: Junos OS Release 11.2 and later
|
|
Description
|
- 4-port: 4 OC3/STM1 or OC12/STM4 ports
- Each port is rate-selectable and supports OC3, OC12, or OC48.
- The ports can be configured to support a combination of OC3, OC12, and OC48 rates. In the combination, you can configure only one port to support OC48, whereas OC3 or OC12 can be configured on all four ports.
- 8-port: 8 OC3/STM1 or OC12/STM4 ports
- Each port is rate-selectable and supports OC3, OC12, or OC48.
- The ports can be configured to support a combination of OC3, OC12, and OC48 rates. In the combination, you can configure only four ports to support OC48, whereas OC3 or OC12 can be configured on all eight ports.
- Power requirement:
- 4-port: 2.6 A @ 9 V (23.4 W)
- 8-port: 3.1 A @ 9 V (27.9 W)
- Weight:
- 4-port: 1.27 lb (0.58 kg)
- 8-port: 1.47 lb (0.67 kg)
- Model number:
- 4-port: MIC-3D-4OC3OC12-1OC48
- 8-port: MIC-3D-8OC3OC12-4OC48
|
|
Hardware features
|
- The ports are labeled:
- 4-port: 0-3
- 8-port: 0-7
- Maximum transmission units (MTUs) of up to 9192 bytes
|
|
Software features
|
- Per-port SONET/SDH framing
- Local and remote loopback on each port
- Optical diagnostics and monitoring
- Clocking options: internal or external/loop mode.
- Unified in-service software upgrade (unified ISSU)
- Encapsulations:
- Multiprotocol Label Switching (MPLS) fast reroute
- MPLS CCC (circuit cross-connect)
- MPLS TCC (translational cross-connect)
- Cisco High-Level Data Link Control
- Cisco HDLC CCC
- Cisco HDLC TCC
- Point-to-Point Protocol (PPP)
- PPP for CCC
- PPP for TCC
- Flexible Frame Relay
- Frame Relay
- Frame Relay for CCC
- Frame Relay for TCC
- PPP over Frame Relay
|
|
Cables and connectors
|
Tip: You can use the Hardware Compatibility Tool to find information about the pluggable transceivers supported on your Juniper Networks device.
The list of supported transceivers for the MX Series is located at https://pathfinder.juniper.net/hct/category/#catKey=100001&modelType;=All&pf;=MX+Series.
|
|
LEDs
|
OK/FAIL LED, one bicolor:
- Green—MIC is functioning normally
- Red—MIC has failed
LINK LED, one green per port:
- Off—Not enabled
- Green—Online with no alarms or failures
- Yellow—Online with alarms for remote failures
- Red—Active with a local alarm; router has detected a failure
|
|
Alarms, errors, and events
|
SONET alarms:
- Loss of light (LOL)
- Loss of signal (LOS)
- Loss of frame (LOF)
- Phase lock loop (PLL)
- Severely errored frame (SEF)
- Alarm indicator signal–line (AIS-L)
- Alarm indicator signal–path (AIS-P)
- Remote defect indicator–line (RDI-L)
- Remote defect indicator–path (RDI-P)
- Loss of pointer–path (LOP-P)
- Bit error rate–signal degrade (BERR-SD)
- Bit error rate–signal fail (BERR-SF)
- Payload label mismatch–Path (PLM-P)
- Unequipped–path (UNEQ-P)
- Remote error indicator–path (REI-P)
SDH alarms:
- Loss of light (LOL)
- Phase lock loop (PLL)
- Loss of frame (LOF)
- Loss of signal (LOS)
- Severely errored frame (SEF)
- Multiplex-section alarm indicator signal (MS-AIS)
- H Path alarm indicator signal (HP-AIS)
- Loss of pointer (LOP)
- Bit error rate–signal degrade (BER-SD)
- Bit error rate–signal fail (BER-SF)
- Multiplex section–far end receive failure (MS-FERF)
- High order path–far end receive failure (HP-FERF)
- High order path–payload label mismatch (HP-PLM)
- Remote error indicator (REI)
- Unequipped (UNEQ)
|
Log In